top of page
Search

The Lambeth Parking Survey Methodology Explained

Writer: Michael Okubajo
Michael Okubajo
1 day ago
5 min read

If you're submitting a planning application in London and the council has asked for a "Lambeth survey", this guide explains what that means: where the method comes from, how the survey is carried out, how parking stress is calculated and what happens next.

Short on time? We can scope and run the survey for you. See our parking stress surveys.

What is the Lambeth Methodology?

The Lambeth Methodology is the parking survey method set out in Lambeth Council's Parking Survey Guidance Note. It gives applicants a consistent, repeatable way to show how much on-street parking near a site is already in use. It has become the default method for residential schemes across most of London, and many councils outside London base their own guidance on it.

The current version is the 2021 Guidance Note. It doesn't set a pass or fail threshold. It is a method of measurement, and the council decides what the result means for your scheme.

When is a Lambeth survey needed?

Usually when a development could add parked cars to local streets: new flats or houses with little or no off-street parking, conversions, the loss of garages or forecourt parking, or a change of use that brings in more visitors. Councils ask for one at validation, at pre-application stage or in a highways officer's consultation response.

Step 1: The survey area

For residential schemes, the survey covers all roads within 200 metres walking distance of the site, roughly a two-minute walk. For commercial schemes it is 500 metres, roughly a five-minute walk.

Two points often catch people out:

  • It's walking distance, not a circle. The distance is measured along the roads from the site, not drawn as a radius on a map.

  • Whole stretches of road, not imaginary lines. Drivers don't stop at a 200m line, so the survey is extended to the next junction or cut back to the previous one.

The area can be adjusted, for example to leave out roads in another borough or places where nobody could realistically park. Every exclusion must be listed in the report with the reason, because the case officer will check it.

Step 2: When to survey

The standard residential survey is two snapshot counts on two separate weekday nights, Monday to Thursday, between 00:30 and 05:30. That's when most residents are home and street parking is at its fullest.

Avoid:

  • weeks that include public holidays or school holidays, and the weeks immediately before and after them

  • dates on or close to local events

  • nights affected by roadworks, suspended bays or skips (if they can't be avoided, record them in the report)

Commercial surveys are generally carried out across the proposed opening hours. Extra survey times are needed for sites in a town centre, near places of worship or schools, near other commercial uses, or close to railway stations where commuters park. Agree these with the case officer before you survey.

Step 3: Measure the kerb and work out capacity

Each road in the area is measured and every length of kerb classified:

  • Unrestricted kerb: anyone can park overnight

  • Restrictions that don't apply overnight: for example single yellow lines, depending on their hours

  • Bays: resident permit, pay and display, disabled, car club and so on

  • Unavailable: double yellow and red lines, dropped kerbs and crossovers, bus stops and lay-bys, kerb build-outs, and the first 5 metres from any junction, which is excluded for safety

Available kerb is turned into spaces at 5 metres per car, rounded down. A 37m stretch therefore counts as 7 spaces, not 7.4.

Step 4: Count the cars and calculate parking stress

On each survey night, every parked car is counted road by road. Parking stress is then:

Parking stress (%) = cars parked ÷ available spaces × 100

For example, 120 cars in 150 spaces is 80% stress.

Illustrative example (not a real site):

Road

Available spaces

Night 1 parked

Night 2 parked

Average stress

Road A

40

33

35

85%

Road B

25

18

17

70%

Road C

15

15

14

97%

Total

80

66

66

83%

Stress can exceed 100%, because smaller cars fit into less than 5 metres. Results should be shown road by road as well as in total, so the case officer can see exactly where the pressure is.

The survey should also separate spaces future residents could actually use from spaces they couldn't. For example, bays in a neighbouring permit zone shouldn't be counted as available to them.

Step 5: What the result means

The Lambeth guidance sets no threshold. It simply notes that an unacceptable increase in parking stress can be a reason for refusal. In practice, many London highway officers treat streets at around 85% or more as heavily parked, but each borough judges results against its own policies, so check before you rely on a figure.

What usually follows:

  • Comfortable result: the survey supports the proposed parking arrangements.

  • High result: the council may still approve with a car-free or permit-free legal agreement, car club membership, more cycle parking or a travel plan, especially where public transport access (PTAL) is good.

  • Very high result with poor PTAL: the scheme may need changing, for example by adding off-street spaces or reducing the number of homes.

This is where interpretation matters as much as the counting. → How we carry out and report parking surveys

What a Lambeth survey report should contain

  • the survey dates and times

  • a description of the area and nearby uses that affect parking

  • every excluded area, with the reason

  • anything unusual on the night, such as suspended bays, roadworks or skips

  • a plan, preferably at 1:1250, showing the site, the survey extent and the restrictions

  • a plan of the kerb measurements used to work out capacity (Lambeth may not accept a survey without one)

  • car counts for each road and each night, with approximate positions marked on the plan

  • conclusions and, where needed, recommended mitigation

Common mistakes that get surveys rejected

  1. Drawing a 200m circle instead of measuring walking distance

  2. Surveying in or next to a holiday week, or on a Friday night

  3. Counting spaces future residents couldn't use, such as bays in a neighbouring permit zone

  4. Forgetting the 5m junction exclusion, dropped kerbs or crossovers

  5. Relying on old data, for example a survey done before a new CPZ changed local parking

  6. Not agreeing extra survey times when the site is near a station, school, place of worship or town centre

  7. Leaving out the capacity plan, so the officer can't check the space count

Lambeth Methodology vs other councils' methods

Most London boroughs accept the Lambeth Methodology, but some have their own requirements. Richmond upon Thames uses its own parking beat survey criteria, and some councils ask for extra nights or weekend counts. Always check with the council before booking the survey. → Our guide to parking surveys in Richmond upon Thames

Frequently asked questions

Who can carry out a Lambeth survey? Anyone can, but councils give more weight to surveys from independent transport consultants and can reject surveys that don't follow the method.

Is the Lambeth Methodology used outside London? Yes. Several councils outside London base their own parking survey guidance on it.

Does the Lambeth Methodology apply to commercial developments? Yes, with changes. Commercial schemes use a 500m survey area and are generally surveyed during the proposed opening hours rather than overnight. Agree the times with the council.

Can parking stress be over 100%? Yes. The method assumes 5 metres per car, and smaller cars need less, so more cars can fit than the calculated number of spaces.

Need a Lambeth survey?

Capital Transport Planning carries out Lambeth Methodology parking surveys across London, from agreeing the scope with the council to the final report and the planning case it supports.

Need a parking survey for your scheme? Get in touch for a quote.

Sources

 
 
 

Recent Posts

See All

Comments


Capital Transport Planning logo

​Capital Transport Planning is an independent consultancy delivering expert transport planning and infrastructure solutions across the UK.

  • Facebook
  • Youtube
  • Instagram
  • LinkedIn

Richmond Office,
Greater London

Address: Parkshot House, 5 Kew Road Richmond upon Thames, TW9 2PR

E: info@capitaltp.co.uk
P: +44 (0)208 1681 911

© 2026 by CTP. All rights reserved.

Website Made By DesignByComfy

bottom of page